Category Archives: Civil Laser
520nm 22W Lab Laser Fiber Output PC Control
This is 520nm high power green fiber laser system. This laser adds software control. Use RS232-USB to connect the laser and computer software.The laser output power can be adjusted by software. Using EasyHost software, you can also write your own programs to control the lower computer according to the communication protocol.
The output power is 22W laser, it is a high-power laser, we added a heat sink under the laser module. The heat sink is composed of aluminum sheets and 3 cooling fans. Its fiber is pluggable, here we choose a 1000μm fiber. Let’s check it now.
Software Operation:
Click ‘Open COM’, the software links the lower computer control circuit of the laser. When starting the software for the first time, set the maximum current first, and set a maximum current value according to the laser test report. If the current is too large, it is easy to burn out the laser chip. For each laser, the maximum current must be set first.
915nm 3W IR MM Fiber Coupled Laser System
Usually we often see visible lasers, but few people will test infrared invisible lasers. Today we tested a 915nm infrared laser and its output power of 3000mW. Then when it is coupled through the fiber, what is the output power of the fiber end? Let’s check it now.
The optical fiber can be customized. 100μm~1000μm fiber is optional, the coupling efficiency of different fibers will be somewhat different. The larger the core diameter, the higher the coupling efficiency, usually the coupling efficiency is 80%~90 percent. In addition, the fiber length and interface also can be customzied. Here is 1000μm, SMA interface fiber.
The output power of the laser is adjustable from 0 to 3000mW, which can be adjusted by the knob. It supports 3 working modes, CW/TTL/Analog, switch the working mode on the back of the laser power supply. In TTL/Analog modulation mode, an external modulation signal needs to be connected.
The 915nm laser is an infrared laser, invisible light, we use an infrared sensitive film to observe. Faint light spots can also be photographed with a camera.
772nm Fiber Laser CW Working Mode Operation Video
What we are going to demonstrate in today’s video is a 772nm 1W fiber coupled laser. The output power of the laser is adjustable from 0 to 1000mW, which can be adjusted by the knob. It supports 3 working modes, CW/TTL/Analog, switch the working mode on the back of the laser power supply. In TTL/Analog modulation mode, an external modulation signal needs to be connected.
The optical fiber is pluggable and customizable. The fiber core diameter,fiber length and interface can be customized according to customer needs. 100μm to 1000μm fiber is optional, the coupling efficiency of different fibers will be somewhat different. The larger the core diameter, the higher the coupling efficiency, usually the coupling efficiency is 80%~90%.
The 772nm laser is a near-infrared laser, and the light spot is dim.
660nm Red Semiconductor Laser Coupled Fiber Optic
What I’m going to talk about today is 660nm 1800mW fiber laser system. It supports 3 working modes, CW/TTL/Analog. In TTL/Analog modulation mode, an external modulation signal needs to be connected. In addition, the Lock crystal head cannot be pulled out. External signal Mod Input, no need to connect in CW working mode.
The optic fiber can be customized. Here is 1000μm SMA905 interface fiber. 100μm to 1000μm fiber is optional, the coupling efficiency of different fibers will be somewhat different. The larger the core diameter, the higher the coupling efficiency, usually the coupling efficiency is 80~90%.
To adjust the output power by adjusting the working current:
Turn the ‘Adjustor’ knob clockwise, when the current exceeds the minimum working current, the Laser indicator light turns green, and there is laser output at this time. When the ‘Adjustor’ is rotated clockwise to the end, it is the max working current and the max output power of the laser. In addition, the red STOP button is used for emergency stop, and it is not used under normal circumstances.
1615nm IR Invisible Fiber Laser Source
This is a 1615nm 200mW infrared fiber coupled laser source. The output power is 0~200mW adjustable by adjusting the working current. Turn the ‘Adjustor’ knob on the power supply clockwise, when the current exceeds the minimum working current, the Laser indicator light turns green, and there is laser output at this time. When the ‘Adjustor’ is rotated clockwise to the end, it is the max working current and the max output power of the laser.
The Optical fiber is removable. The optical fiber interface is FC/PC, and it can be customized. The 1615nm laser is an infrared laser, which cannot be observed by the human eye. We use an infrared sensitive film to observe the light spot.
450nm 1500mW Software Control Fiber Laser
Today we are talking about software-controlled laser system. This is 450nm blue fiber coupled laser source controlled by software. EasyHost is the control software. The connection between the laser and PC software adopts the communication protocol of RS232. The laser supports two working modes: CW/Modulation. When switching to Modulation, an external signal input is required. This is a fiber-coupled laser, and a free-space output laser can also be customized.
Software operation:
Click the [Open COM] button to connect the control circuit of the laser. Multiple laser working parameters can be viewed/set in the software. As a special reminder, it is necessary to set amaximum working current parameter according to the current laser, so as to avoid the later adjusted current being too high and damaging the laser.
30dBm EDFA Single-mode Fiber Laser Module
This is a C-Band 30dBm module type EDFA. It is equipped with SMF-28e single-mode fiber, and polarization-maintaining fiber can also be customized. This is a high-power EDFA, with a row of aluminum sheets on one side of the shell for easy heat dissipation. This is a modular design, and desktop EDFA can also be customized. Let’s check it now.
High power erbium doped fiber amplifier (EYDFA-HP-BA)，based on amplification technology of double clad erbium doped fiber， unique optical packaging technology, and with reliable hardware light path protection design, realized high power laser output in C band or L band， It has the advantages of high gain and low noise, and can be widely used in CATV, optical fiber communication, laser radar, etc..
The test report & spectrum analysis chart of C-Band 30dBm SM EDFA.
The relationship between power current and output power.
1064nm Infrared Laser 10W High Power DPSS Laser
It is 1064nm high power laser with heat sink at the bottom of the laser head. It adopts air cooling mode, with 2 cooling fans. The light outlet has a protective cover. The modulation mode can be selected from the original TTL or Analog, and upgraded to be compatible with both.
When the key is turned ON, the laser starts to work. The knob is to adjust the current size, thereby adjusting the laser output power. Preheat for 1 to 5 minutes, and the laser power reaches the maximum value.
The connector connecting the laser head to the power supply has a protective cover. When installing the laser, it needs to be unscrewed first.
SM Fiber Laser System SLD Broadband Light Source
SLD broadband light source adopts super radiant semiconductor diode light-emitting chip, which outputs broadband spectrum with low coherence degree and high output optical power spectral density. The operating wavelength can be selected from O, S, C, L and other bands, suitable for optical OCT, optical fiber sensing applications.
This is a 1550nm 10mW SLD light source of module type. It is equipped with a single mode fiber. It can be customized power adjustable version. When the power adjustment is selected, the power adjustment is controlled through the RS232 serial communication. The standard version is a fixed power mode, the light source is controlled by the button. We tested it with an infrared photosensitive film, and we could see a light spot.
The test data report and spectrum of 1550nm light source.
Ultra Narrow Linewidth 3kHz PM Fiber Laser Source
This is a 1550nm 50mW PM fiber laser source. The output power can be adjusted, and the adjustment accuracy is 0.1mW. This is a narrow linewidth laser with a spectral bandwidth of less 3kHz. Customizable software control function, using RS232 communication serial port. Standard version with button control, control switch, adjust the power size. PM1550 polarization maintaining fiber is installed, and SM single-mode fiber can also be customized. Let’s check it now.
Single frequency narrow linewidth fiber laser adopts rare earth doped fiber DFB laser cavity structure, output single longitudinal mode laser with wavelength of 1550nm, spectral linewidth is less than 3kHz, output spectral side mode suppression ratio exceeds 60dB, can provide module or desktop package, is distributed Ideal laser source for applications such as sensing.
The test report of 1550nm 50mW 3kHz PM fiber laser.
This is the line width test, the actual measurement is 0.95kHz.
